Minolta QUICKSCAN35 Manuel d'instructions

1Thank you for purchasing the Minolta QuickScan 35. The QuickScan 35 enables you to scan bothnegative and positive, color and monochrome (black &

10You will need to set an SCSI identification (ID) number for thescanner. Each SCSI device connected to your computer musthave a different SCSI ID num

111. Connect one end of the SCSI cable to one of the two SCSIports on the rear panel of the QuickScan 35 and the other end tothe SCSI port on the rear

123. INSTALLING THESOFTWAREThe QuickScan 35 comes with Photoshop Plug-in software andUtility software. If you do not have Photoshop or if you want tos

135. SCAN FLOW CHARTPlace film in the film holder emulsion side down; then insert thefilm holder to the scanner as indicated on the holder.Choose the

14SCANNING IMAGESBefore you start Photoshop or the Utility software, turn on theQuickScan 35.If you are using the Utility software, double click on th

15If the computer cannot confirm interface because the QuickScan 35power is off or there is a problem with the SCSI connection or theSCSI ID number, a

162.INSERTING THE FILMThe QuickScan 35 can scan both color and monochrome (black &white), positive and negative 35mm film. Both film in slide moun

173. SPECIFYING THE FILM TYPESpecifying the type of film you are scanning is necessary for anaccurate reproduction of the image. There are four types

185.1. Image Orientation ButtonThe image orientation button enables you to specify the correctorientation of your image before scanning. The image in

192. Choose the scan pitch from the scan pitch pop-up menu. 3. Crop the image as desired. The number of pixels will changeaccordingly to maintain the

2END-USER LICENSE AGREEMENTCAREFULLY READ THE LICENSE AGREEMENT BELOW BEFORE OPENING THIS PACKAGEDSOFTWARE. OPENING THIS PACKAGE INDICATES YOUR ACCEPT

203. Crop the image as desired. The scan pitch changesautomatically from 1 to 24 to maintain the pixel number.･ Click RESET to return to the default s

216.3. Print Mode1. Choose Print Mode from the scan mode pop-up menu.2. Enter the resolution you want for the final image in the outputresolution box.

227. SCANNING THEIMAGEWhen you have finished making all the adjustments to the image,you are ready to scan the film. Click Scan. The control paneldisa

23IMAGE ADJUSTMENTYou can adjust the color balance, brightness, and black level ofthe image. Click the image adjustment button to display thecontrols.

243. BRIGHTNESS ADJUSTMENTThe color level at a curser’s position on the preview image isdisplayed in the lower right corner of the preview window and

25MANUAL FOCUSNormally, focusing is not necessary with the QuickScan 35,however, it is recommended when your final image will be largeand if the film

26SAVE AND LOADBUTTONSThe Save and Load buttons enable you to save and load severaldifferent scanner settings. These saved settings are very usefulwhe

27COLOR SYNCColor Sync compensates for the different color characteristics ofeach instrument (i.e., monitor or printer) connected to theMacintosh. 1.

282. OPERATION1.If you have already used Color Sync, drag the QuickScan 35file to the Color Sync Profiles folder in the Initial Settings folder.2.Drag

29TROUBLE SHOOTINGQ:The Macintosh does not start up after connecting theQuickScan 35.A:Turn power off, then check SCSI cable, SCSI connection, andSCSI

3FOR PROPER AND SAFE USEVarious symbols are used throughout this instruction manual andon the product itself for your proper and safe use of this prod

30SPECIFICATIONSType:Film transport type Usable Film:35mm negative/positive, color/monochrome (black &white) filmsScanning Dimensions:24.2mm x 36.

9223-2880-11(P9506-A506)

INSTRUCTION MANUAL

4RISK OF FIRE OR ELECTRIC SHOCKDo not use voltage other than what is indicated.RISK OF FIRE OR ELECTRIC SHOCKDo not place a container of water or oth

5CAUTIONRISK OF FIRE OR ELECTRIC SHOCKGrasp the plug when removing the power cord from an outlet. Pulling thecord may damage it resulting in fire or e

6TABLE OF CONTENTSINTRODUCTIONEND-USER LICENSE AGREEMENTFOR PROPER AND SAFE USETABLE OF CONTENTSBEFORE YOU BEGIN1. Package Contents2. System Requireme

7BEFORE YOU BEGIN1. Package ContentsThe following contents should be included in this package.• QuickScan 35• SCSI cable SC-1• Power cord• SCSI termin

8NAMES OF PARTS1.SCANNER

9PREVIEW SCAN WINDOW897171234561011121314 15161. Auto eject check box2. Film eject button3. Save button4. Load button5. Film type pop-up menu6. Image